DSA-3110-A1 bootlog¶
Trying NPE-C...success. Using NPE-C with PHY 1.
Ethernet lan: MAC address 00:03:47:df:32:a8
IP: 192.168.0.43/255.255.255.0, Gateway: 192.168.0.91
Default server: 192.168.0.90
RedBoot(tm) bootstrap and debug environment [ROM]
Red Hat certified release, version 2.04 - built 15:36:45, Jan 11 2011
Platform: KIXRP435 Development Platform (IXP43X) BE
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2007 Free Software Foundation, Inc.
RAM: 0x00000000-0x10000000, [0x00030f48-0x0ffc1000] available
FLASH: 0x50000000 - 0x50400000, 32 blocks of 0x00020000 bytes each.
rtk_switch_init - set shared meter successfully
(1310),(1075)
(1310),(1075)
rtk_port_macForceLinkExt0_set - set shared meter successfully
RedBoot> load -b 0x200000 DSA-3110-A1/kernel.gz.tramp
Using default protocol (TFTP)
Entry point: 0x00200054, address range: 0x00200000-0x0039dbb6
RedBoot> go
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-BETA1 #15 r0:224704M: Mon Aug 15 14:57:09 EEST 2011
[email protected]:/usr/obj/usr/home/ray/work/DDTeam.net/ZRouter/zrouter/tmp/arm.armeb/usr/1/MIPS_FreeBSD/HEAD/head/sys/usr/obj/usr/home/ray/work/DDTeam.net/ZRouter/zrouter/conf/D-Link_DSA-3110-A1 arm
Preloaded elf kernel "elf kernel" at 0xc05a6ee4.
module_register: module gpio_cambria/gpiobus already exists!
Module gpio_cambria/gpiobus failed to register: 17
CPU: IXP435 rev 1 (ARMv5TE) (XScale core)
DC enabled IC enabled WB enabled LABT branch prediction enabled
32KB/32B 32-way Instruction cache
32KB/32B 32-way write-back-locking Data cache
real memory = 268435456 (256 MB)
Physical memory chunk(s):
0x654000 - 0xfb1afff, 256667648 bytes (62663 pages)
avail memory = 255578112 (243 MB)
ULE: setup cpu 0
firmware: 'npe_fw' version 0: 46444 bytes loaded at 0xc056d730
random: <entropy source, Software, Yarrow>
mem: <memory>
crypto: <crypto core>
null: <null device, zero device>
ixp0: <Intel IXP4XX> on motherboard
ixp0: 37fff<RCOMP,USB,HASH,AES,DES,HDLC,AAL,HSS,UTOPIA,ETH0,ETH1,PCI>
pcib0: <IXP4XX PCI Bus> on ixp0
pci0: <PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1191, dev=0x000d, revid=0x01
domain=0, bus=0, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x0d (3250 ns)
intpin=a, irq=0
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0x100, size 8, port disabled
map[14]: type I/O Port, range 32, base 0x200, size 8, enabled
map[18]: type I/O Port, range 32, base 0x300, size 8, enabled
map[1c]: type I/O Port, range 32, base 0x400, size 8, enabled
map[20]: type I/O Port, range 32, base 0x500, size 8, enabled
map[24]: type Memory, range 32, base 0x48000000, size 12, memory disabled
pcib0: routing pin 1 for (null)
found-> vendor=0x10ec, dev=0x8167, revid=0x10
domain=0, bus=0, slot=3, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=0
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0, size 8, port disabled
map[14]: type Memory, range 32, base 0, size 8, memory disabled
pcib0: routing pin 1 for (null)
found-> vendor=0x10ec, dev=0x8167, revid=0x10
domain=0, bus=0, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=0
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0, size 8, port disabled
map[14]: type Memory, range 32, base 0, size 8, memory disabled
pcib0: routing pin 1 for (null)
ahci0: <Acard ATP8620-A AHCI SATA controller> port 0x100-0x1ff,0x200-0x2ff,0x300-0x3ff,0x400-0x4ff,0x500-0x5ff mem 0x48000000-0x48000fff irq 28 at device 1.0 on pci0
ahci0: AHCI v1.00 with 2 3Gbps ports, Port Multiplier supported
ahci0: Caps: 64bit AL CLO 3Gbps PM SSC PSC 32cmd 2ports
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich0: Caps: HPCP
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich1: Caps: HPCP
re0: <RealTek 8169SC/8110SC Single-chip Gigabit Ethernet> irq 26 at device 3.0 on pci0
re0: Lazy allocation of 0x100 bytes rid 0x10 type 4 at 0
re0: MSI count : 0
re0: MSI-X count : 0
re0: Chip rev. 0x18000000
re0: MAC rev. 0x00000000
DUMP PHY1:
1140 796d 001c c912 01e1 41e1 0007 2001 41e1 0000 0000 0000 1007 f880 0000 3000
0060 6c00 0000 2c40 1060 0000 c739 2108 2740 8c00 0040 0162 846c 0000 0123 0000
miibus0: <MII bus> on re0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0: OUI 0x00e04c, model 0x0011, rev. 2
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
re0: bpf attached
re0: Ethernet address: 00:e0:4c:69:21:54
re1: <RealTek 8169SC/8110SC Single-chip Gigabit Ethernet> irq 25 at device 4.0 on pci0
re1: Lazy allocation of 0x100 bytes rid 0x10 type 4 at 0x600
re1: MSI count : 0
re1: MSI-X count : 0
re1: Chip rev. 0x18000000
re1: MAC rev. 0x00000000
DUMP PHY1:
1140 7949 001c c912 01e1 0000 0004 2001 0000 0000 0000 0000 1007 f880 0000 3000
0060 4040 0000 0040 1060 0000 0838 2108 2740 8c00 0040 4013 8409 0000 0123 0000
miibus1: <MII bus> on re1
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: OUI 0x00e04c, model 0x0011, rev. 2
ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
re1: bpf attached
re1: Ethernet address: 00:e0:4c:69:21:54
ixpclk0: <IXP4XX Timer> on ixp0
ixpiic0: <IXP4XX GPIO-Based I2C Interface> on ixp0
iicbb0: <I2C bit-banging driver> on ixpiic0
iicbus0: <Philips I2C bus> on iicbb0 master-only
iic0: <I2C generic I/O> on iicbus0
gpio_cambria0: <Gateworks Cambria GPIO driver> at addr 0x56 on iicbus0
gpiobus0: <GPIO bus> on gpio_cambria0
gpiobus0: GPIO device with 5 pins
gpioc0: <GPIO controller> at pin(s) 0-4 on gpiobus0
ad74180: <Analog Devices AD7418 ADC> at addr 0x50 on iicbus0
ds1672_rtc0: <Dallas Semiconductor DS1672 RTC> at addr 0xd0 on iicbus0
device_attach: ds1672_rtc0 attach returned 2
ixpwdog0: <IXP4XX Watchdog Timer> on ixp0
uart0: rclk 14745600
uart0: ixp425_alloc_resource: assign 0xc8000000:0x1000 A4X
uart0: rclk 14745600
uart0: ixp425_alloc_resource: assign 0xc8000000:0x1000 A4X
uart0: <Non-standard ns8250 class UART with FIFOs> on ixp0
uart0: ixp425_alloc_resource: assign 0xc8000000:0x1000 A4X
uart0: fast interrupt
uart0: console (115200,n,8,1)
ixpqmgr0: <IXP4XX Q-Manager> on ixp0
npe0: using npe.0.npeid=C override
npe0: <IXP NPE-C> on ixp0
npe0: using npe.0.npeid=C override
npe0: using npe.0.mac=C override
npe0: MAC at 0xc800a000
npe0: using npe.0.mii=C override
npe0: MII at 0xc800a000
npe0: load fw image IXP425.NPE-C Func 0x5 Rev 2.1
npe0: bpf attached
npe0: Ethernet address: 00:03:47:df:32:a8
npe1: using npe.1.npeid=A override
npe1: <IXP NPE-A> on ixp0
npe1: using npe.1.npeid=A override
npe1: using npe.1.mac=A override
npe1: MAC at 0xc800c000
npe1: using npe.1.mii=C override
npe1: MII at 0xc800a000
npe1: load fw image IXP435/IXP465.NPE-A Func 0x82 Rev 2.0
npe1: bpf attached
cfi0: EXP_TIMING_CS0_OFFSET 0xbfff3c42
cfi0: ixp425_alloc_resource: assign 0x50000000:0x400000
cfi_do_query: query at 0 with mask 0xff (w=2, s=4)
cfi_do_query: cfi_read(sc, ofs, CFI_QRY_IDENT) return 0x7
cfi_do_query: query at 0 with mask 0xff (w=2, s=2)
cfi_do_query: cfi_read(sc, ofs, CFI_QRY_IDENT) return 0x51
cfi0: detected with bus width = 2, address shift = 2
cfi0: Array mask = 0xff
cfi0: <Intel/Sharp - 4MB> on ixp0
cfi0: ixp425_alloc_resource: assign 0x50000000:0x400000
cfi0:
cfi0: [32x128KB]
cfid0 on cfi0
gpio_avila0: <Gateworks Avila GPIO driver> on ixp0
gpiobus1: <GPIO bus> on gpio_avila0
gpiobus1: GPIO device with 16 pins
gpioc1: <GPIO controller> at pin(s) 0-15 on gpiobus1
ehci0: <IXP4XX Integrated USB 2.0 controller> on ixp0
ehci0: ixp425_alloc_resource: assign 0xcd000000:0x1000
usbus0: EHCI version 1.0
usbus0: stop timeout
usbus0: set host controller mode
usbus0: set big-endian mode
usbus0: <IXP4XX Integrated USB 2.0 controller> on ehci0
usbus0: bpf attached
ehci0: usbpf: Attached
ehci1: <IXP4XX Integrated USB 2.0 controller> on ixp0
ehci1: ixp425_alloc_resource: assign 0xce000000:0x1000
usbus1: EHCI version 1.0
usbus1: stop timeout
usbus1: set host controller mode
usbus1: set big-endian mode
usbus1: <IXP4XX Integrated USB 2.0 controller> on ehci1
usbus1: bpf attached
ehci1: usbpf: Attached
cryptosoft0: <software crypto> on motherboard
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
Timecounter "IXP4XX Timer" frequency 66666600 Hz quality 1000
Timecounters tick every 10.000 msec
vlan: initialized, using hash tables with chaining
IPsec: Initialized Security Association Processing.
lo0: bpf attached
enc0: bpf attached
GEOM: new disk cfid0
g_redboot_taste: mediasize 4194304 secsize 4 blksize 131072 offmask 0x3fffff
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ahcich0: AHCI reset...
ahcich0: SATA connect timeout time=10000us status=00000000
ahcich0: AHCI reset: device not found
ahcich1: AHCI reset...
ahcich1: SATA connect timeout time=10000us status=00000000
ahcich1: AHCI reset: device not found
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
hwpmc: XSCALE/4/32/0x1ff<INT,USR,SYS,EDG,THR,REA,WRI,INV,QUA>
uhub0: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered
ugen0.2: <Kingston> at usbus0
umass0: <Kingston DT 101 II, class 0/0, rev 2.00/1.10, addr 2> on usbus0
Root mount waiting for: usbus0
umass0:2:0:-1: Attached to scbus2
Trying to mount root from cd9660:/dev/map/rootfs.uncompress []...
mountroot: waiting for device /dev/map/rootfs.uncompress ...
(probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0?
(probe0:umass-sim0:0:0:0): SCSI status error
(probe0:umass-sim0:0:0:0): . CDB: 0 0 0 0 0 0
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: UNIT ATTENTION asc:28,0 ()
(probe0:umass-sim0:0:0:0): Retrying command (per sense data)
pass0 at umass-sim0 bus 0 scbus2 target 0 lun 0
pass0: <Kingston DT 101 II PMAP> Removable Direct Access SCSI-0 device
pass0: Serial Number 0019E00149F7B9B1E000010C
pass0: 40.000MB/s transfers
da0 at umass-sim0 bus 0 scbus2 target 0 lun 0
da0: <Kingston DT 101 II PMAP> Removable Direct Access SCSI-0 device
da0: Serial Number 0019E00149F7B9B1E000010C
da0: 40.000MB/s transfers
da0: 3827MB (7837696 512 byte sectors: 255H 63S/T 487C)
GEOM: new disk da0
Mounting from cd9660:/dev/map/rootfs.uncompress failed with error 19.
Loader variables:
Manual root filesystem specification:
<fstype>:<device> [options]
Mount <device> using filesystem <fstype>
and with the specified (optional) option list.
eg. ufs:/dev/da0s1a
zfs:tank
cd9660:/dev/acd0 ro
(which is equivalent to: mount -t cd9660 -o ro /dev/acd0 /)
? List valid disk boot devices
. Yield 1 second (for background tasks)
<empty line> Abort manual input
mountroot> ufs:/dev/da0s1
Trying to mount root from ufs:/dev/da0s1 []...
warning: no time-of-day clock registered, system time will not be set accurately
start_init: trying /sbin/init
/etc/rc: cannot create /dev/led/status: No such file or directory
0/IN
1/II
2/PU
3/INT
ioctl(GPIOSETCONFIG): Invalid argument
ifconfig: interface arge0 does not exist
ifconfig: interface arge1 does not exist
kenv: unable to get LAN_MAC_ADDR
ifconfig: interface lan0 does not exist
kenv: unable to get WAN_MAC_ADDR
ifconfig: interface wan0 does not exist
kenv: unable to get HostName
kern.coredump: 1 -> 0
net.inet.ip.forwarding: 0 -> 1
kldload: can't load random: File exists
Aug 12 13:56:01 syslogd: bind: Can't assign requested address
syslogd: child pid 48 exited with return code 1
ipfw2 initialized, divert loadable, nat loadable, rule-based forwarding disabled, default to deny, logging disabled
ipfw0: bpf attached
65000 allow ip from any to any
WARNING: attempt to domain_add(netgraph) after domainfinalize()
Generating public/private rsa1 key pair.
Your identification has been saved in /etc/ssh/ssh_host_key.
Your public key has been saved in /etc/ssh/ssh_host_key.pub.
The key fingerprint is:
ff:9c:ab:e5:32:3a:3d:ae:18:3a:cf:37:c7:df:3a:59 root@
The key's randomart image is:
+--[RSA1 1024]----+
| |
| |
| |
| |
| S |
| . E |
| . o. .o |
| .o o+ B=oo |
| .o+.oBo*O+. |
+-----------------+
Generating public/private dsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_dsa_key.
Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub.
The key fingerprint is:
3e:c9:66:cd:94:75:78:3d:be:ba:b2:6b:72:85:4c:cc root@
The key's randomart image is:
+--[ DSA 1024]----+
| |
| . . |
| o o o..|
| E o. .|
| S = . . |
| o = o . .|
| B o . . |
| o o + . |
| +o+o. |
+-----------------+
Generating public/private rsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_rsa_key.
Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub.
The key fingerprint is:
d4:21:00:a5:f0:7e:2e:9f:73:2b:3c:9c:f6:13:eb:a8 root@
The key's randomart image is:
+--[ RSA 2048]----+
| . .oo.. . |
| o . o . |
| o . . |
| . . |
| . . S |
| o . |
| .o.. o |
| oOo+ |
| Eo+B+o |
+-----------------+
Starting collector.
Aug 12 13:57:07 getty[104]: open /dev/ttyu1: No such file or directory
login: root
Password:
FreeBSD 9.0-CURRENT / ZRouter project
Developed by Aleksandr Rybalko <[email protected]>
under sponsorship from the Petri Consulting and
D-Link International Pte Ltd Ukraine.
Welcome to FreeBSD!
#