DIR-632 A1¶
The D-Link® Wireless N 8-Port Router (DIR-632) has 8 10/100 LAN Ports, enabling you to connect up to 8 Ethernet-enabled devices, such as an entire entertainment system, a home office or a wired network to your Wireless N 300 Router.
- Easy to use, easy to set up
- Create a high-speed Wi-Fi home network with superior coverage for small homes and apartments
- Network up to 8 ethernet-enabled devices to connect various entertainment devices
- Built-in QoS engine enhances performance for basic gaming and video streaming
- Share a USB printer or storage device across your network
Specifications¶
| Revision | A1 | |
| Firmware | D-link | 1.4.1 2013/01/09 |
| CPU | Atheros AR7242-AH1A @ 400Mhz | MIPS32 24Kc |
| Board | AP99 or AP101 ??? | |
| Wireless | Atheros AR9287-BL1A | 802.11b (max. 11 Mbit/s), 802.11g (max. 54 Mbit/s), 802.11n (max. 300 Mbit/s, 2.4 GHz only) |
| Ethernet | RMC RTL8309G | 1x WAN RJ-45 10/100 Base T, 8x LAN RJ-45 10/100 Base T |
| ROM | ? | 8mb |
| RAM | Zentel A3S56D40FTP-G5 | 32MB |
| USB | OHCI (USB1.1), EHCI (USB2.0) | 1x USB2.0 (support USB hub, 3G modem - DWM-156 3G) |
| LEDs | Power, WLAN (Wireless Connection), LAN (10/100), Internet Status | |
| Antennas | 2x antennas | |
| FCC ID | KA2IR632A1 | |
| Serial | YES | (+3.3V,Write,Read,GND) |
| JTAG | YES | |
| Dimensions | Item 230mm x 150mm x 33mm | Packaging 276.9mm x 66mm x 205.8mm |
| Weight | Item 272.2 grams | Packaging: 907.2 grams |
How to restore to factory firmware (FAILSAFE MODE):¶
- Download the original firmware from http://ftp.dlink.ru/pub/Router/DIR-632/Firmware/
- DON'T Unplug one LAN cable, other and WAN - unplug.
- Configure a Windows (*nux, *bsd) computer with IP address in the 192.168.0.2, subnet 255.255.255.0
- Hold down reset button with a pin, unplug power from the router or bent paperclip for 15 seconds
- While still holding reset button down, plug router power cable back in and hold down the reset button 15 seconds
- Open at Browser (FIREFOX - working) http://192.168.0.1
- Click browse and select your firmware file
- Click send, and wait a minute or 2. if it works your status light will turn green, you are supposed to get a page that says upload succeeded, I waited 5 minutes and it didn't happen. It still worked.
- Reset router by holding down reset button for 10 seconds, status light will go orange again but don't worry it is just rebooting.
- You should be good to go, open a new browser window and type 192.168.0.1 and you should get the Dlink login page. If this doesn't work, try again from step 1
Serial Port¶
| № | Name |
| 1 | +3.3V |
| 2 | Write from PC |
| 3 | Read to PC |
| 4 | GND |
JTAG port¶
empty
MTD¶
Bootloader version (printenv in serial console):¶
256k - u-boot
64k - nvram
1984k - linux
5568k - rootfs
64k - MAC
192k - LP
64k - ART
Original firmware version:¶
Creating 9 MTD partitions on "ar7240-nor0":| Address | MTD part. |
| 0x00000000-0x00040000 | "u-boot" |
| 0x00040000-0x00050000 | "nvram" |
| 0x00050000-0x00240000 | "linux" |
| 0x00240000-0x007b0000 | "rootfs" |
| 0x007b0000-0x007c0000 | "MAC" |
| 0x007c0000-0x007f0000 | "LP" |
| 0x007f0000-0x00800000 | "ART" |
| 0x00050000-0x007b0000 | "Linux" |
| 0x00000000-0x00800000 | "ALL" |
cat /proc/mtd
| dev: | size | erasesize | name |
| mtd0: | 00040000 | 00010000 | "u-boot" |
| mtd1: | 00010000 | 00010000 | "nvram" |
| mtd2: | 001f0000 | 00010000 | "linux" |
| mtd3: | 00570000 | 00010000 | "rootfs" |
| mtd4: | 00010000 | 00010000 | "MAC" |
| mtd5: | 00030000 | 00010000 | "LP" |
| mtd6: | 00010000 | 00010000 | "ART" |
| mtd7: | 00760000 | 00010000 | "Linux" |
| mtd8: | 00800000 | 00010000 | "ALL" |