zrouter

h1. DSA-3110-A1 bootlog

<pre>

Trying NPE-C...success. Using NPE-C with PHY 1.

Ethernet lan: MAC address 00:03:47:df:32:a8

IP: 192.168.0.43/255.255.255.0, Gateway: 192.168.0.91

Default server: 192.168.0.90

RedBoot(tm) bootstrap and debug environment [ROM]

Red Hat certified release, version 2.04 - built 15:36:45, Jan 11 2011

Platform: KIXRP435 Development Platform (IXP43X) BE

Copyright (C) 2000, 2001, 2002, 2003, 2004, 2007 Free Software Foundation, Inc.

RAM: 0x00000000-0x10000000, [0x00030f48-0x0ffc1000] available

FLASH: 0x50000000 - 0x50400000, 32 blocks of 0x00020000 bytes each.

rtk_switch_init - set shared meter successfully

(1310),(1075)

(1310),(1075)

rtk_port_macForceLinkExt0_set - set shared meter successfully

RedBoot> load -b 0x200000 DSA-3110-A1/kernel.gz.tramp

Using default protocol (TFTP)

Entry point: 0x00200054, address range: 0x00200000-0x0039dbb6

RedBoot> go

KDB: debugger backends: ddb

KDB: current backend: ddb

Copyright (c) 1992-2011 The FreeBSD Project.

Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994

	The Regents of the University of California. All rights reserved.

FreeBSD is a registered trademark of The FreeBSD Foundation.

FreeBSD 9.0-BETA1 #15 r0:224704M: Mon Aug 15 14:57:09 EEST 2011

    [email protected]:/usr/obj/usr/home/ray/work/DDTeam.net/ZRouter/zrouter/tmp/arm.armeb/usr/1/MIPS_FreeBSD/HEAD/head/sys/usr/obj/usr/home/ray/work/DDTeam.net/ZRouter/zrouter/conf/D-Link_DSA-3110-A1 arm

Preloaded elf kernel "elf kernel" at 0xc05a6ee4.

module_register: module gpio_cambria/gpiobus already exists!

Module gpio_cambria/gpiobus failed to register: 17

CPU: IXP435 rev 1 (ARMv5TE) (XScale core)

  DC enabled IC enabled WB enabled LABT branch prediction enabled

  32KB/32B 32-way Instruction cache

  32KB/32B 32-way write-back-locking Data cache

real memory  = 268435456 (256 MB)

Physical memory chunk(s):

0x654000 - 0xfb1afff, 256667648 bytes (62663 pages)

avail memory = 255578112 (243 MB)

ULE: setup cpu 0

firmware: 'npe_fw' version 0: 46444 bytes loaded at 0xc056d730

random: <entropy source, Software, Yarrow>

mem: <memory>

crypto: <crypto core>

null: <null device, zero device>

ixp0: <Intel IXP4XX> on motherboard

ixp0: 37fff<RCOMP,USB,HASH,AES,DES,HDLC,AAL,HSS,UTOPIA,ETH0,ETH1,PCI>

pcib0: <IXP4XX PCI Bus> on ixp0

pci0: <PCI bus> on pcib0

pci0: domain=0, physical bus=0

found->	vendor=0x1191, dev=0x000d, revid=0x01

	domain=0, bus=0, slot=1, func=0

	class=01-00-00, hdrtype=0x00, mfdev=0

	cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)

	lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x0d (3250 ns)

	intpin=a, irq=0

	powerspec 2  supports D0 D1 D2 D3  current D0

	map[10]: type I/O Port, range 32, base 0x100, size  8, port disabled

	map[14]: type I/O Port, range 32, base 0x200, size  8, enabled

	map[18]: type I/O Port, range 32, base 0x300, size  8, enabled

	map[1c]: type I/O Port, range 32, base 0x400, size  8, enabled

	map[20]: type I/O Port, range 32, base 0x500, size  8, enabled

	map[24]: type Memory, range 32, base 0x48000000, size 12, memory disabled

pcib0: routing pin 1 for (null)

found->	vendor=0x10ec, dev=0x8167, revid=0x10

	domain=0, bus=0, slot=3, func=0

	class=02-00-00, hdrtype=0x00, mfdev=0

	cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords)

	lattimer=0x00 (0 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)

	intpin=a, irq=0

	powerspec 2  supports D0 D1 D2 D3  current D0

	map[10]: type I/O Port, range 32, base 0, size  8, port disabled

	map[14]: type Memory, range 32, base 0, size  8, memory disabled

pcib0: routing pin 1 for (null)

found->	vendor=0x10ec, dev=0x8167, revid=0x10

	domain=0, bus=0, slot=4, func=0

	class=02-00-00, hdrtype=0x00, mfdev=0

	cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords)

	lattimer=0x00 (0 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)

	intpin=a, irq=0

	powerspec 2  supports D0 D1 D2 D3  current D0

	map[10]: type I/O Port, range 32, base 0, size  8, port disabled

	map[14]: type Memory, range 32, base 0, size  8, memory disabled

pcib0: routing pin 1 for (null)

ahci0: <Acard ATP8620-A AHCI SATA controller> port 0x100-0x1ff,0x200-0x2ff,0x300-0x3ff,0x400-0x4ff,0x500-0x5ff mem 0x48000000-0x48000fff irq 28 at device 1.0 on pci0

ahci0: AHCI v1.00 with 2 3Gbps ports, Port Multiplier supported

ahci0: Caps: 64bit AL CLO 3Gbps PM SSC PSC 32cmd 2ports

ahcich0: <AHCI channel> at channel 0 on ahci0

ahcich0: Caps: HPCP

ahcich1: <AHCI channel> at channel 1 on ahci0

ahcich1: Caps: HPCP

re0: <RealTek 8169SC/8110SC Single-chip Gigabit Ethernet> irq 26 at device 3.0 on pci0

re0: Lazy allocation of 0x100 bytes rid 0x10 type 4 at 0

re0: MSI count : 0

re0: MSI-X count : 0

re0: Chip rev. 0x18000000

re0: MAC rev. 0x00000000

DUMP PHY1:

 1140 796d 001c c912 01e1 41e1 0007 2001 41e1 0000 0000 0000 1007 f880 0000 3000

 0060 6c00 0000 2c40 1060 0000 c739 2108 2740 8c00 0040 0162 846c 0000 0123 0000

miibus0: <MII bus> on re0

ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0

ukphy0: OUI 0x00e04c, model 0x0011, rev. 2

ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow

re0: bpf attached

re0: Ethernet address: 00:e0:4c:69:21:54

re1: <RealTek 8169SC/8110SC Single-chip Gigabit Ethernet> irq 25 at device 4.0 on pci0

re1: Lazy allocation of 0x100 bytes rid 0x10 type 4 at 0x600

re1: MSI count : 0

re1: MSI-X count : 0

re1: Chip rev. 0x18000000

re1: MAC rev. 0x00000000

DUMP PHY1:

 1140 7949 001c c912 01e1 0000 0004 2001 0000 0000 0000 0000 1007 f880 0000 3000

 0060 4040 0000 0040 1060 0000 0838 2108 2740 8c00 0040 4013 8409 0000 0123 0000

miibus1: <MII bus> on re1

ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1

ukphy1: OUI 0x00e04c, model 0x0011, rev. 2

ukphy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow

re1: bpf attached

re1: Ethernet address: 00:e0:4c:69:21:54

ixpclk0: <IXP4XX Timer> on ixp0

ixpiic0: <IXP4XX GPIO-Based I2C Interface> on ixp0

iicbb0: <I2C bit-banging driver> on ixpiic0

iicbus0: <Philips I2C bus> on iicbb0 master-only

iic0: <I2C generic I/O> on iicbus0

gpio_cambria0: <Gateworks Cambria GPIO driver> at addr 0x56 on iicbus0

gpiobus0: <GPIO bus> on gpio_cambria0

gpiobus0: GPIO device with 5 pins

gpioc0: <GPIO controller> at pin(s) 0-4 on gpiobus0

ad74180: <Analog Devices AD7418 ADC> at addr 0x50 on iicbus0

ds1672_rtc0: <Dallas Semiconductor DS1672 RTC> at addr 0xd0 on iicbus0

device_attach: ds1672_rtc0 attach returned 2

ixpwdog0: <IXP4XX Watchdog Timer> on ixp0

uart0: rclk 14745600

uart0: ixp425_alloc_resource: assign 0xc8000000:0x1000 A4X

uart0: rclk 14745600

uart0: ixp425_alloc_resource: assign 0xc8000000:0x1000 A4X

uart0: <Non-standard ns8250 class UART with FIFOs> on ixp0

uart0: ixp425_alloc_resource: assign 0xc8000000:0x1000 A4X

uart0: fast interrupt

uart0: console (115200,n,8,1)

ixpqmgr0: <IXP4XX Q-Manager> on ixp0

npe0: using npe.0.npeid=C override

npe0: <IXP NPE-C> on ixp0

npe0: using npe.0.npeid=C override

npe0: using npe.0.mac=C override

npe0: MAC at 0xc800a000

npe0: using npe.0.mii=C override

npe0: MII at 0xc800a000

npe0: load fw image IXP425.NPE-C Func 0x5 Rev 2.1

npe0: bpf attached

npe0: Ethernet address: 00:03:47:df:32:a8

npe1: using npe.1.npeid=A override

npe1: <IXP NPE-A> on ixp0

npe1: using npe.1.npeid=A override

npe1: using npe.1.mac=A override

npe1: MAC at 0xc800c000

npe1: using npe.1.mii=C override

npe1: MII at 0xc800a000

npe1: load fw image IXP435/IXP465.NPE-A Func 0x82 Rev 2.0

npe1: bpf attached

cfi0: EXP_TIMING_CS0_OFFSET 0xbfff3c42

cfi0: ixp425_alloc_resource: assign 0x50000000:0x400000

cfi_do_query: query at 0 with mask 0xff (w=2, s=4)

cfi_do_query: cfi_read(sc, ofs, CFI_QRY_IDENT) return 0x7

cfi_do_query: query at 0 with mask 0xff (w=2, s=2)

cfi_do_query: cfi_read(sc, ofs, CFI_QRY_IDENT) return 0x51

cfi0: detected with bus width = 2, address shift = 2

cfi0: Array mask = 0xff

cfi0: <Intel/Sharp - 4MB> on ixp0

cfi0: ixp425_alloc_resource: assign 0x50000000:0x400000

cfi0: 

cfi0: [32x128KB]

cfid0 on cfi0

gpio_avila0: <Gateworks Avila GPIO driver> on ixp0

gpiobus1: <GPIO bus> on gpio_avila0

gpiobus1: GPIO device with 16 pins

gpioc1: <GPIO controller> at pin(s) 0-15 on gpiobus1

ehci0: <IXP4XX Integrated USB 2.0 controller> on ixp0

ehci0: ixp425_alloc_resource: assign 0xcd000000:0x1000

usbus0: EHCI version 1.0

usbus0: stop timeout

usbus0: set host controller mode

usbus0: set big-endian mode

usbus0: <IXP4XX Integrated USB 2.0 controller> on ehci0

usbus0: bpf attached

ehci0: usbpf: Attached

ehci1: <IXP4XX Integrated USB 2.0 controller> on ixp0

ehci1: ixp425_alloc_resource: assign 0xce000000:0x1000

usbus1: EHCI version 1.0

usbus1: stop timeout

usbus1: set host controller mode

usbus1: set big-endian mode

usbus1: <IXP4XX Integrated USB 2.0 controller> on ehci1

usbus1: bpf attached

ehci1: usbpf: Attached

cryptosoft0: <software crypto> on motherboard

crypto: assign cryptosoft0 driver id 0, flags 100663296

crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0

crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0

Timecounter "IXP4XX Timer" frequency 66666600 Hz quality 1000

Timecounters tick every 10.000 msec

vlan: initialized, using hash tables with chaining

IPsec: Initialized Security Association Processing.

lo0: bpf attached

enc0: bpf attached

GEOM: new disk cfid0

g_redboot_taste: mediasize 4194304 secsize 4 blksize 131072 offmask 0x3fffff

usbus0: 480Mbps High Speed USB v2.0

usbus1: 480Mbps High Speed USB v2.0

ahcich0: AHCI reset...

ahcich0: SATA connect timeout time=10000us status=00000000

ahcich0: AHCI reset: device not found

ahcich1: AHCI reset...

ahcich1: SATA connect timeout time=10000us status=00000000

ahcich1: AHCI reset: device not found

ugen0.1: <Intel> at usbus0

uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0

ugen1.1: <Intel> at usbus1

uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1

hwpmc: XSCALE/4/32/0x1ff<INT,USR,SYS,EDG,THR,REA,WRI,INV,QUA>

uhub0: 1 port with 1 removable, self powered

uhub1: 1 port with 1 removable, self powered

ugen0.2: <Kingston> at usbus0

umass0: <Kingston DT 101 II, class 0/0, rev 2.00/1.10, addr 2> on usbus0

Root mount waiting for: usbus0

umass0:2:0:-1: Attached to scbus2

Trying to mount root from cd9660:/dev/map/rootfs.uncompress []...

mountroot: waiting for device /dev/map/rootfs.uncompress ...

(probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0?

(probe0:umass-sim0:0:0:0): SCSI status error

(probe0:umass-sim0:0:0:0): . CDB: 0 0 0 0 0 0 

(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error

(probe0:umass-sim0:0:0:0): SCSI status: Check Condition

(probe0:umass-sim0:0:0:0): SCSI sense: UNIT ATTENTION asc:28,0 ()

(probe0:umass-sim0:0:0:0): Retrying command (per sense data)

pass0 at umass-sim0 bus 0 scbus2 target 0 lun 0

pass0: <Kingston DT 101 II PMAP> Removable Direct Access SCSI-0 device 

pass0: Serial Number 0019E00149F7B9B1E000010C

pass0: 40.000MB/s transfers

da0 at umass-sim0 bus 0 scbus2 target 0 lun 0

da0: <Kingston DT 101 II PMAP> Removable Direct Access SCSI-0 device 

da0: Serial Number 0019E00149F7B9B1E000010C

da0: 40.000MB/s transfers

da0: 3827MB (7837696 512 byte sectors: 255H 63S/T 487C)

GEOM: new disk da0

Mounting from cd9660:/dev/map/rootfs.uncompress failed with error 19.

Loader variables:

Manual root filesystem specification:

  <fstype>:<device> [options]

      Mount <device> using filesystem <fstype>

      and with the specified (optional) option list.

    eg. ufs:/dev/da0s1a

        zfs:tank

        cd9660:/dev/acd0 ro

          (which is equivalent to: mount -t cd9660 -o ro /dev/acd0 /)

  ?               List valid disk boot devices

  .               Yield 1 second (for background tasks)

  <empty line>    Abort manual input

mountroot> ufs:/dev/da0s1

Trying to mount root from ufs:/dev/da0s1 []...

warning: no time-of-day clock registered, system time will not be set accurately

start_init: trying /sbin/init

/etc/rc: cannot create /dev/led/status: No such file or directory

0/IN

1/II

2/PU

3/INT

ioctl(GPIOSETCONFIG): Invalid argument

ifconfig: interface arge0 does not exist

ifconfig: interface arge1 does not exist

kenv: unable to get LAN_MAC_ADDR

ifconfig: interface lan0 does not exist

kenv: unable to get WAN_MAC_ADDR

ifconfig: interface wan0 does not exist

kenv: unable to get HostName

kern.coredump: 1 -> 0

net.inet.ip.forwarding: 0 -> 1

kldload: can't load random: File exists

Aug 12 13:56:01  syslogd: bind: Can't assign requested address

syslogd: child pid 48 exited with return code 1

ipfw2 initialized, divert loadable, nat loadable, rule-based forwarding disabled, default to deny, logging disabled

ipfw0: bpf attached

65000 allow ip from any to any

WARNING: attempt to domain_add(netgraph) after domainfinalize()

Generating public/private rsa1 key pair.

Your identification has been saved in /etc/ssh/ssh_host_key.

Your public key has been saved in /etc/ssh/ssh_host_key.pub.

The key fingerprint is:

ff:9c:ab:e5:32:3a:3d:ae:18:3a:cf:37:c7:df:3a:59 root@

The key's randomart image is:

+--[RSA1 1024]----+

|                 |

|                 |

|                 |

|                 |

|        S        |

|         .    E  |

|      .  o. .o   |

|    .o o+ B=oo   |

|    .o+.oBo*O+.  |

+-----------------+

Generating public/private dsa key pair.

Your identification has been saved in /etc/ssh/ssh_host_dsa_key.

Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub.

The key fingerprint is:

3e:c9:66:cd:94:75:78:3d:be:ba:b2:6b:72:85:4c:cc root@

The key's randomart image is:

+--[ DSA 1024]----+

|                 |

|             . . |

|          o o o..|

|           E o. .|

|        S = .  . |

|       o = o .  .|

|        B o .  . |

|       o o +  .  |

|          +o+o.  |

+-----------------+

Generating public/private rsa key pair.

Your identification has been saved in /etc/ssh/ssh_host_rsa_key.

Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub.

The key fingerprint is:

d4:21:00:a5:f0:7e:2e:9f:73:2b:3c:9c:f6:13:eb:a8 root@

The key's randomart image is:

+--[ RSA 2048]----+

|  . .oo.. .      |

|   o .   o .     |

|    o   . .      |

|   .   .         |

|    . . S        |

|     o  .        |

|    .o.. o       |

|     oOo+        |

|    Eo+B+o       |

+-----------------+

Starting collector.

Aug 12 13:57:07 getty[104]: open /dev/ttyu1: No such file or directory

login: root

Password:

FreeBSD 9.0-CURRENT / ZRouter project

Developed by Aleksandr Rybalko <[email protected]>

under sponsorship from the Petri Consulting and

D-Link International Pte Ltd Ukraine.

Welcome to FreeBSD!

#

</pre>