RouterStation Pro » History » Version 1
Maciej Milewski, 01/25/2012 10:45 PM
Added Ubiquiti RouterStation Pro description and flash instructions.
| 1 | 1 | Maciej Milewski | h1. RouterStation Pro |
|---|---|---|---|
| 2 | 1 | Maciej Milewski | |
| 3 | 1 | Maciej Milewski | Board for wireless routers made by Ubiquiti. |
| 4 | 1 | Maciej Milewski | |
| 5 | 1 | Maciej Milewski | h2. Quick Specification |
| 6 | 1 | Maciej Milewski | |
| 7 | 1 | Maciej Milewski | Atheros AR7161 MIPS 24K running @ 680MHz |
| 8 | 1 | Maciej Milewski | 128MB of DDR RAM |
| 9 | 1 | Maciej Milewski | 16MB of SPI FLASH |
| 10 | 1 | Maciej Milewski | 3 MINI-PCI Slots(supports Type IIIA) |
| 11 | 1 | Maciej Milewski | 1 WAN Gbit port (arge0) (connected through AR8216 switch chip) |
| 12 | 1 | Maciej Milewski | 3 LAN Gbit ports (arge1) (connected through AR8216 switch chip) |
| 13 | 1 | Maciej Milewski | USB 2.0 Port |
| 14 | 1 | Maciej Milewski | RS232/DB9 Connector |
| 15 | 1 | Maciej Milewski | SDIO(SD Card socket) |
| 16 | 1 | Maciej Milewski | Onboard RTC(Real Time Clock) |
| 17 | 1 | Maciej Milewski | DC Power Jack (48V) |
| 18 | 1 | Maciej Milewski | 802.3af 48V compatible |
| 19 | 1 | Maciej Milewski | |
| 20 | 1 | Maciej Milewski | Additional information on [[http://wiki.ubnt.com/RouterStation_Pro]] |
| 21 | 1 | Maciej Milewski | |
| 22 | 1 | Maciej Milewski | h3. Firmware flashing |
| 23 | 1 | Maciej Milewski | |
| 24 | 1 | Maciej Milewski | Default board IP: 192.168.1.20 |
| 25 | 1 | Maciej Milewski | Default boot script: |
| 26 | 1 | Maciej Milewski | <pre> |
| 27 | 1 | Maciej Milewski | fis load -d -e kernel |
| 28 | 1 | Maciej Milewski | exec |
| 29 | 1 | Maciej Milewski | </pre> |
| 30 | 1 | Maciej Milewski | |
| 31 | 1 | Maciej Milewski | 1.Connect board to the ethernet and serial adapter. |
| 32 | 1 | Maciej Milewski | 2.You may: |
| 33 | 1 | Maciej Milewski | a)enter automatic rescue mode by pressing reset during power up of the board or |
| 34 | 1 | Maciej Milewski | b)After connecting power press Ctrl+C to stop running redboot sequence. To enter rescue mode type:<pre>urescue</pre> |
| 35 | 1 | Maciej Milewski | 3.On your terminal run tftp in binary mode to put the firmware image into board:<pre>tftp 192.168.1.20 |
| 36 | 1 | Maciej Milewski | binary |
| 37 | 1 | Maciej Milewski | put firmware.img</pre> |
| 38 | 1 | Maciej Milewski | |
| 39 | 1 | Maciej Milewski | You should observe flash sequence on your serial terminal. |